Allen 446 Manuel de réparation

1AOPERATIONS1A-71.5 Technical Data Honda Engines1.5 Technical Data Kawasaki EnginesEngine Make and Honda 4.0 Honda 5.5 Honda 8.0 Honda 11 Honda 13Mode

430 72" 1828mm 436 72” 1828mm442 78”1981mm 446 78” 1981mm430 32" 812mm 436 38” 965mm442 44”1118mm 446 48” 1219mm430 36" 914mm 436 36” 9

1AOPERATIONS1A-9Throttle LeverChoke LeverFuel ON/OFFCrank Wheel Pull HandleEngine ON/OFFThe Razorback®Walker is a modern high production machine. Fini

Push down on the handle tomove the rotor assembly to theright. Pull up on the handle assembly tomove the rotor assembly to theleft.1.10 Steering1.11 P

1AOPERATIONS1A-111.12 Periodic Maintenance ScheduleThe chart below lists basic engine maintenance. Refer to engine manufacturer's Operation Manua

1.14 Drive BeltsABCDDEFigure 1Figure 2Figure 3To Replace Belts: 1. Remove belt guard (A) by removing the four belt guard mounting bolts (B). See fi

1AOPERATIONS1A-13Damage to, or replacement of, a trowel arm can changethe adjustment of the lift lever. This can unbalance thetrowel arms and cause th

2A-1Step 1Step 2Step 3STEP 1: Un-pack the handle assembly(A) and the lowerunit from their boxes. Check to make sure no damagewas done during shipment

3APARTS3A-1INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PAGE(S)Lower End Assembly . . . . . . . . . .

3A-2LOWER END ASSEMBLY3APARTS

WWalk Behind Talk Behind TrowelrowelOPERATIONSASSEMBLYPARTSMANUALINSTRUCTIONSBOOKPRINTED 1/03THIS MANUAL COVERS WALKBEHIND TROWEL(S) BELOW430 EDGING W

3A-3ILL. PART # DESCRIPTION QTY. 1 . . . . . . .037619 . . . . . . .RING, 436 . . . . . . . . . . . . .1 . . . . . . . .038674 . . . . . . .RING, 44

3APARTSHANDLE ASSEMBLY3A-4FINE PITCHILL. PART # DESCRIPTION QTY. 1. . . . . . . . .037668 . . . . . . . .GRIP . . . . . . . . . . . . . . . . . . .

ILL. PART # DESCRIPTION QTY. 1. . . . . . . . . . . .019427 . . . . . .KNOB, BURLOP PLASTIC 1-7/8 . . . . . . . . . . .

GEARBOX ASSEMBLY3APARTS3A-6

ILL. PART # DESCRIPTION QTY. 1. . . . . . . . . . . . . . .015205 . . . . . . . . . . .SCREW, 5/16-18 x 1 . .

3A-83APARTSSFC GEARBOX ASSEMBLY

3A-93APARTSSFC GEARBOX ASSEMBLY (cont’d)ILL. PART # DESCRIPTION QTY. 1. . . . . . . . . . . . . . .032745 . .

3A-103APARTSILL. PART # DESCRIPTION QTY. 1. . . . . . . . . . . . . . .013370 . . . . . . . . . . .SCREW, 10-3

ILL. PART # DESCRIPTION QTY. 1. . . . . . . . . . . . . . .027242 . . . . . . . . . . .BELT GUARD (8 & 11

3A-123APARTS037248 -- 430 EDGER PAN026910 -- 436 PAN039218 -- 436 EDGER PAN033997 -- 442 PANSPIDER PULLER035688ALIGNMENT JIG01686310 POUND WEIGHT01064

LIMITED WLIMITED WARRANTYARRANTYAllen Engineering Corporation warrants its products to be free of defects in material or workmanship for the fol-lowi

1AOPERATIONS1A-1THE INFORMATION CONTAINED IN THIS MANUAL WAS BASED ON MACHINES IN PRODUC-TION AT THE TIME OF PUBLICATION. ALLEN ENGINEERING RESERVES T

1AOPERATIONS1A-2Identification PlateAn identification plate listing the MODEL, NAME, and SERIAL NUMBER is attached to each unit andis located on the f

1AOPERATIONS1A-3IMPORTANT REMINDERFill out your Allen Engineering Corp. warranty card and place it in the mail within 24 hours of delivery.Complete ot

1AOPERATIONS1A-4Operating Information430, 436, 442, 446, 446SD, 446SD SFC 1.1 Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. Read operating and safety instructions before using the Razorback®Walker and operate the machine in accordance with the manufacturer's inst

1AOPERATIONS1A-61.4 Service SafetyPoorly maintained equipment can become a safety hazard! In order for the equipment to operate safe-ly and properly o